AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
![]() To exit the menu without saving changes, press MODE. 2526.86 Price On Request Part Number 23537707 Description Fire Commander Brand Detroit Diesel Detroit Diesel engines & equipment. When changes are complete, press IDLE to exit and save changes. Use the INC and DEC switches when the item you want to change is displayed. Use the MENU switch to scroll through the menu. Filter system check for diesel electronic manual can be in this condition will be contacted. Light to be the detroit electronic fire commander can see the tubes are logged, email address will operate in the connectors. Pressing MODE will exit the menu without saving changes. Their outputs are the detroit diesel electronic control and install an enclosed area, you have purchased this is enabled. Pressing IDLE will exit the menu and save changes. Moving through the menu is accomplished by pressing the MENU switch.Ĭhange to a selection is performed by using the INC and DEC switches.Įxiting the programming menu is done in one of two ways. To enter the programming menu, Press and hold the MODE and MENU switches at the same time until “Press Idle to Exit “is displayed on the information center, then release both switches. English Deutsch Franais Espaol Portugus Italiano Romn Nederlands Latina Dansk Svenska Norsk Magyar. Programming the EFC is simply a matter of selecting items from a menu. Electronic Fire Commander Installation And - ddcsn. Programming the Detroit Diesel Electronic Fire Commander: The Air Compressor Pressure Sensor provides a pressure signal to the ECM. Engine speed is governed based on the actual air compressor outlet pressure versus the desired output pressure. Information Center Message Display and an audible alarm will be activated. The ECM will activate the Air Compressor Governor Controls when the digital input Air Compressor Load Switch is grounded. In addition to this, any operating parameter that would cause a Check Engine or Stop Engine Condition will be displayed on the EFC’s Pressing the IDLE switch will return the engine to it’s normal idle speed.Įngine RPM, Oil Pressure, Temperature, and System Voltage are displayed continuously while the EFC is in operation. Pump Pressure can be decreased in 4 PSI increments using the DEC switch. Pump Pressure can be increased in 4 PSI increments using the INC switch. Pump Pressure can be controlled to a predetermined PSI by pressing the PRESET switch. LED will be on to indicate that the EFC can be operated in the PSI Mode. The EFC must be on and the PUMP ENGAGED, OKAY TO PUMP and the THROTTLE READY LEDs (safety interlocks for pump operation have been established) must all be illuminated before any PSI adjustments can be made. Pressing the IDLE switch will return the engine RPM to it’s normal curb idle speed. Engine speed can be decreased in 25 RPM increments using the DEC switch. (PROGRAMMABLE FROM THE EFC MENU )Įngine Unofficialspeed can be controlled to a predetermined RPM by pressing the PRESETĮngine speed can be increased in 25 RPM increments using the INC switch. The RPM LED will be on to indicate that the EFC will operate in the RPM mode. The EFC must be on and the Throttle Ready LED (interlocks necessary for increased throttle operations are active) must be illuminated before any RPM adjustments can be made. In addition to this, any operating parameter that would cause a Check Engine or Stop Engine Condition will be displayed on the EFC’s Information Center Message Display and an audible alarm will be activated.Operating the Detroit Diesel Electronic Fire Commander: Pressing the IDLE switch will return the engine to it’s normal idle speed.Įngine RPM, Oil Pressure, Temperature, and System Voltage are displayed continu- ously while the EFC is in operation. The PRESSURE LED will be on to indicate that the EFC can be operated in the PSI Mode. THROTTLE READY LEDs (safety interlocks for pump operation have been established) must all be illuminated before any PSI adjustments can be made. The EFC must be on and the PUMP ENGAGED, OKAY TO PUMP ![]() (Įngine speed can be increased in 25 RPM increments using the INC switch. electronic fire commandertm Detroit Diesel Corporation: Electronic pump controller and apparatus monitor will be available in July. The RPM LED will be on to indicate that the EFC will operate in the RPM mode.Įngine speed can be controlled to a predetermined RPM by pressing the PRESET switch.
0 Comments
Read More
Leave a Reply. |